We present the first integrated study of carbonate, hydroxyl, fluoride, and chloride ion partitioning in the apatite-melt system. We determined volatile partitioning behavior between apatite and silicate melt for both haplobasaltic andesite and trachyte bulk compositions at 0.5–1 GPa and 1250°C using the piston-cylinder apparatus. All volatile species were analyzed directly in both apatite and glass using secondary ion mass spectrometry (SIMS) and electron probe microanalysis. Distribution coefficients for OH-halogen exchange are similar to those from previous studies, and together with literature data, reveal a significant log-linear relationship with temperature, while the effects of pressure and melt composition are minimal. Meanwhile, halogen-free experiments generate very high C contents (up to 5000 ppm) in apatite. Stoichiometry calculations and infrared spectra indicate that this C is mainly incorporated onto the channel volatile site together with hydroxyl. In halogen-bearing experiments, apatite crystals contain significantly lower C (≤500 ppm), which may be partly incorporated onto the phosphate site while the channel volatile site is filled by OH+F+Cl+C. Our experiments give the first constraints on H2O-CO2 exchange between apatite and silicate melt, with a KD of 0.355 ± 0.05 for the trachyte and 0.629 ± 0.08 for the haplobasaltic andesite. The new constraints on the temperature-dependence of partitioning will enable quantitative modeling of apatite-volatile exchange in igneous systems, while this new partitioning data and method for direct, in situ analysis of C in apatite mark a significant advance that will permit future studies of magmatic C and other volatiles. This has a broad range of potential applications including magmatic differentiation, fractionation, and degassing; quantification of volatile budgets in extraterrestrial and deep earth environments; and mineralization processes.
Volatile-bearing minerals such as apatite represent a useful source of information about the volatile compositions of the systems from which they crystallize. Apatite has a very flexible mineral structure, and igneous apatites can accommodate all the major volatile species of magmatic importance, i.e., H, C, F, Cl, and S, as well as other trace volatile species such as Br and I (e.g., Peng et al. 1997; Pan and Fleet 2002; Marks et al. 2012; Konecke et al. 2017). With some knowledge of the partitioning properties of these volatiles, apatite may be able to, therefore, provide quantitative information about multi-component degassing, and other processes, in terrestrial magmas. The apatite crystal formula is Ca5(PO4)3X, where X represents the channel volatile site that runs parallel to the crystallographic c-axis and is typically occupied by OH, F, and Cl. While there are several existing studies focusing on exchange between OH and halogens in the channel site (e.g., Mathez and Webster 2005; Webster et al. 2009, 2017; Doherty et al. 2014; Li and Hermann 2015, 2017; McCubbin et al. 2015; Potts et al. 2015), we are not aware of any previous work quantitatively examining the partitioning behavior of C between apatite and a silicate melt. Knowledge of the C partitioning behavior would be particularly valuable for studies of terrestrial volcanism because magmatic CO2 contents are difficult to infer using traditional methods such as melt inclusions. The solubility of CO2 in silicate melts is strongly dependent on pressure, which means that CO2 is typically degassed very early during magma ascent, and the highest (primary) CO2 contents are generally thought not to be trapped in melt inclusions, or are lost to shrinkage bubbles (e.g., Bureau et al. 1999; Wallace 2005; Blundy et al. 2010; Hartley et al. 2014; Moore et al. 2015; Wallace et al. 2015; Aster et al. 2016). Furthermore, it is commonly not clear as to the extent to which melt inclusions have been affected either by post-entrapment diffusive modification (e.g., Gaetani et al. 2012) or by fluxing of CO2-rich fluids through the magma reservoir during entrapment (e.g., Spilliaert et al. 2006; Collins et al. 2009; Blundy et al. 2010). The existing work on quantitative determination of carbonate contents of apatite is based on FTIR using doubly polished, oriented wafers. This level of sample preparation is almost prohibitively difficult for magmatic apatites, which are typically small microphenocrysts or inclusions in other magmatic mineral phases. Here we successfully determine C in apatite using secondary ion mass spectrometry, and present data from a series of high-pressure and high-temperature experiments allowing us to constrain the combined partitioning behavior of H, C, F, and Cl between apatite and silicate melts.
Our experimental approach was to examine volatile partitioning and exchange equilibria between apatite and silicate melts, with a particular focus on C and OH. We added halogens (F and Cl) in a subset of runs, to evaluate the extent to which this affects the partitioning of C and/or OH. The terminal run pressures (1.0 and 0.5 GPa) and temperatures (1250°C) employed represent reasonable storage conditions for mid- to lower-crustal mafic magmas. Our chosen run conditions have the added advantages that (1) apatite + melt are commonly the only phases present, and (2) the glass fraction of run products is typically greater than 50% (e.g., Prowatke and Klemme 2006). These conditions simplify interpretation of the partitioning data and ensure that suitably sized areas of glass are available for ion microprobe analysis. Furthermore, it is helpful to avoid crystallization of other volatile-bearing phases (e.g., amphibole), which could complicate analysis of the partitioning behavior of volatiles between apatite and melt.
Experimental starting materials
We used two sets of synthetic starting materials (“BA” and “BM”; Table 1), allowing us to investigate the possible compositional effects on volatile partitioning. Both starting materials are based on compositions used in previous experimental studies and were chosen to take advantage of existing phase equilibrium constraints. Composition “BA” is a haplobasaltic andesite equivalent to composition SH3 of Prowatke and Klemme (2006). This composition produced large apatite crystals in trace-element partitioning experiments at similar temperatures and pressures (Prowatke and Klemme 2006) and enabled us to consider volatile partitioning in a simplified, Fe-free system in the first instance. Composition “BM” is a trachyte equivalent to the natural “ZAC” obsidian composition from Campi Flegrei, Naples, Italy (Fabbrizio and Carroll 2008). The nominal compositions of both starting materials are given in Table 1.
Starting materials were prepared as mechanical mixtures of reagent grade oxides (Al2O3, SiO2, MgO, MnO, FeO, Fe2O3, TiO2) and carbonates (Na2CO3, K2CO3, CaCO3), subsequently doped with varying amounts of phosphate [added as Ca3(PO4)2] and volatiles (added as described below). Prior to mixing, all components were dried overnight at 100°C; the oxide powders SiO2, Al2O3, MgO, and TiO2 were additionally fired at 1000°C to drive off residual moisture. Dried components were then mixed in the desired proportions, ground under ethanol to produce homogenous powders, and slowly decarbonated in a box furnace (600 to 1000°C over 6 h). For starting material “BA,” four such powders were produced: a P-bearing split doped with ~25% Ca3(PO4)2; a P-free split equivalent to that reported in Table 1, but with added Ca; and carbonated equivalents of both the P-free and P-bearing splits. Calcium was added to the P-free splits such that all splits had equal bulk CaO contents. In the case of C-bearing splits, the carbonate component was added following the decarbonation step. In this way, the bulk proportions of P and C in each run were varied by varying the proportions of the different splits added to each capsule. F and Cl were added directly to each capsule as Ca-, K-, or Na-fluorides and chlorides. Because the quantity of F and Cl added was small (typically <1 wt%), these additions did not significantly affect the proportions of the other components. Hydrogen, where present, was added as liquid water as described below.
Starting material “BM” was prepared as above, but with an additional glassing step following decarbonation: splits were heated to 1400°C for 30 min in a gas mixing furnace, then ground dry to homogenize. The gas mixture was held near Ni-NiO buffer conditions at the furnace temperature. This heating and grinding process was repeated 1–3 times for each split. Fluorides and chlorides were added to prior to glassing, with carbonate added afterward as above, and splits were mixed to yield the desired bulk volatile proportions (excepting water) before being added to each capsule. These additional steps were employed to ensure the thorough homogenization of starting materials as needed to aid apatite growth and equilibration in a companion study at lower experimental temperatures and pressures. As we observe no systematic textural differences between the apatites produced by the BA and BM starting materials, we assume that the starting powders were sufficiently homogenized during equilibration at high temperatures to negate any potential differences owing to the different preparations of the two starting materials.
Starting powders were loaded into 3 mm diameter Pt capsules. In water-bearing experiments, distilled, deionized water was first added to the base of each capsule using a micro-syringe. Capsules were welded shut, then pressed into cylinders approximately 4 mm in length, and placed into 4 mm diameter outer Pt capsules containing identical proportions of starting powders ± H2O. The outer capsule was then welded shut and pressed into a cylindrical shape approximately 7–8 mm in length. Pressing of inner and outer capsules helped to ensure an even distribution of surrounding materials in the nested assembly. The double-capsule technique employed is essential when using Pt capsules, to reduce gradients in the chemical potentials of H and C adjacent to the sample, and thus limit the rate of H2 and C exchange between the sample and the apparatus (Hall et al. 2004; Brooker et al. 1998). In lieu of a solid buffer, this method also helps to maintain a fixed fO2 (or fH2) in the inner capsule and helps to minimize volatile loss or gain during runs. After each welding step (inner and outer capsule), capsules were weighed to check for water loss, then heated and reweighed to ensure the integrity of the weld seal.
All experiments were run in end-loaded piston-cylinder apparatus (Boyd and England 1960) at the University of Bristol. A conventional ½ inch diameter vessel and piston was used for runs at 1 GPa. A ¾ inch diameter vessel was used for two runs at lower pressure (0.5 GPa). The complete sample assembly consisted of the 4 mm diameter outer Pt capsule surrounded by crushable MgO (½ inch diameter setup; for the geometry of this setup, see McDade et al. 2002, their Fig. 1d) or Al2O3 (¾ inch diameter setup, for the geometry of this setup, see McDade et al. 2002, their Fig. 1e) spacers positioned to center the capsule in the hot spot of the graphite furnace. The furnace + capsule assembly was fitted within a Pyrex sheath and an outer NaCl (½ inch) or talc (¾ inch) sleeve. Loaded assemblies were then heated and pressurized according to a “hot piston in” routine. After applying an initial pressure load, the assembly was allowed to settle for at least 20 min. Temperature and pressure were then increased simultaneously, with the final pressure applied upon reaching the run temperature. This routine is in keeping with that used to determine the talc- and salt-pyrex friction correction for set pressures (~3%, McDade et al. 2002). Pressure was maintained by means of an automated pressure regulator to within ±1 psi of the target run pressure, yielding pressure variations of <<1% relative. Run temperature was monitored using W97Re3–W75Re25 (D-type) thermocouples, inserted along the assembly axis adjacent to the top of the charge. Temperature was maintained by automated adjustment of the operating power via a Eurotherm, with typical deviations from target of <1°C. No attempt was made to correct temperatures for a pressure-dependence of e.m.f., although this effect is generally considered negligible for the type of thermocouple used here (Brooker and Kjarsgaard 2011).
To encourage growth of experimental apatites, runs were first heated to super-liquidus temperatures (1450–1500°C), and then cooled at a constant rate to a terminal temperature of 1250°C, following Prowatke and Klemme (2006). Super-liquidus heating reduces the availability of nuclei and/or secondary nucleation sites for crystallizing phases, fostering the growth of fewer, larger crystals. A slow cooling ramp results in lower degrees of undercooling and thus further favors crystal growth over nucleation (e.g., Swanson 1977). Typical cooling rates were 20 or 50°C/h, depending on the bulk water content. Even lower cooling rates (≤10°C/h) were applied to some runs with lower bulk phosphate contents or nominally zero bulk OH contents (Table 2). Samples were then allowed to equilibrate at the final run temperature, during which time a small temperature cycle was applied (±10°C at 1°C/min) to enhance crystal growth (e.g., Mills and Glazner 2013). Total run times ranged from 20–24 h and were chosen to provide sufficient time for crystal-melt equilibration, as evidenced by experiments at similar conditions (Prowatke and Klemme 2006), while minimizing the time available for diffusive exchange at high temperatures. At the end of each run, charges were quenched isobarically by cutting the operating power while manually maintaining the terminal run pressure.
Following quench, capsules were removed from the assembly and sectioned using a micro-saw. To preserve the double capsule assembly, it was not possible to pierce inner capsules to test for the presence of a free fluid phase, and instead we take the absence of vesicles or gas pockets in most experiments as evidence of volatile undersaturation (two “BM” samples containing minor vesicles are indicated in Table 2). Sectioned capsules were ground using abrasive SiC papers (220 to 1200 grit) and progressively polished using diamond suspensions (6, 3, and 1 μm). Polished capsules were then mounted either in In metal or a thin layer of EpoFix resin, with the aim of minimizing H backgrounds during subsequent ion microprobe analysis.
Electron probe microanalysis
Apatite and glass major element compositions were determined by electron probe microanalysis using a Cameca SX100 5-spectrometer instrument at the University of Bristol. Glasses were analyzed using a 15 kV, 2 nA electron beam defocused to a 15 μm spot, with Na analyzed first to minimize alkali migration (Morgan and London 1996; Humphreys et al. 2006). Apatites were analyzed using a 15 kV, 10 nA beam defocused to 10 μm to minimize migration of halogens yet still enable accurate determination of minor elements (e.g., Goldoff et al. 2012; Stock et al. 2015; see Supplemental1 methods for details of analytical protocol). Calibration standards were albite for Na and Si; St. Johns olivine for Mg; sanidine for Al and K; Durango apatite for P; wollastonite or Durango apatite for Ca; ilmenite for Ti and Fe; Mn metal for Mn; MgF2 for F; and NaCl for Cl. Count times were 30 s on peak for all elements except Fe and Mn (60 s on peak) and Cl and F (120 s on peak). Resulting detection limits for volatile elements in apatite were typically ~120 ppm for Cl and ~500 ppm for F, whereas in glass the detection limits were typically ~300 ppm for Cl and ~900 ppm for F (for full analytical conditions see Supplemental1 materials). Raw data were processed using a PAP matrix correction scheme. Accuracy and precision of the analytical setup were monitored by repeated analysis of well-characterized secondary standards (KN18, BCR2, and synthetic F-bearing haplobasalt for glasses; oriented Durango and Wilberforce apatite crystals for apatite).
Secondary ion mass spectrometry
Volatile compositions of apatite and coexisting glass were determined by secondary ion mass spectrometry using a Cameca ims-4f instrument at the NERC ion microprobe facility at the University of Edinburgh. The instrument is run utilizing Charles Evans and Associates PXT interface and software.
For apatite, a 5 nA 16O- primary beam with a net impact energy of 14.5 keV was accelerated onto the sample. An energy window of 75 ± 20 V was applied. The spot size was ~15–20 μm. A circular field aperture with an effective radius of 8 μm was used to lower H and C backgrounds coming from the edge of the sputtering pit. Backgrounds were monitored using either end-member (H-free) apatites from Schettler et al. (2011) or a piece of quartz embedded within each sample mount.
In addition, a 4 min pre-sputter period at a raster size of 20 μm was employed to minimize contamination from the sample surface. The secondary ions 1H+, 12C+, 25Mg2+, 19F+, 23Na+, 26Mg+, 30Si+, 31P+, 35Cl+, 39K+, and 44Ca+ were collected for 5, 10, 6, 10, 2, 5, 2, 2, 10, 3, and 2 s, respectively, for each 6 cycles of the magnet. Only H2O, CO2, F, P2O5, and Cl were quantified. Other elements were used to monitor for contamination with the silicate glass. The OH and CO32– contents of apatite were determined using daily working curves of 1H/44Ca vs. OH and 12C/44Ca vs. C acquired for a suite of natural apatite standards (Supplemental1 materials), after correction for isobaric interference by 24Mg2+ on 12C (correction generally <5%, except in the most C-poor samples up to 15%). The same approach was taken for both F and Cl, with 95% prediction intervals calculated for every calibration line (Supplemental1 materials). For a small subset of apatite crystals (<15 μm in smallest dimension), the beam current was reduced to 2 nA resulting in a spot size of <10 μm. This process reduced the number of ions counted, but had no appreciable effect on the calibration curve slopes. Halogens were also quantified for halogen-free experiments as a check for contamination. No effect of apatite orientation (parallel vs. perpendicular to the c-axis) on working curves for H2O, CO2, F, and Cl was detected, consistent with the findings of Stock et al. (2015).
For the glass, a similar analytical setup and procedures were used as for apatite, apart from using a 50 ± 20 V energy window for C analysis (a 75 ± 20 V energy window was used for analysis of H and other elements). To ensure accurate determination of C contents in the Mg-rich glass, an initial set of analyses was collected at sufficient mass resolution to separate the 12C+ and 24Mg2+ peaks, with secondary ions collected at 24Mg2+, 12C+, 26Mg+, and 30Si+ for 5, 10, 3, and 2 s, respectively, for each of 10 cycles of the magnet. In a second set of analyses on the same spot (with a 2 min pre-sputter period and 20 μm raster), the secondary ions 1H+, 11B+, 19F+, 26Mg+, 30Si+, and 35Cl+ were collected for 3, 3, 6, 2, 2, and 6 s, respectively (over 10 magnet cycles,). As with apatite, H2O and CO2 contents of the glasses were determined using daily working curves of 1H/30Si vs. H2O and 12C/30Si·SiO2 vs. CO2, respectively, generated from standard glasses including basalts and phonolites. The calibration glasses included samples from Shishkina et al. (2010), Hauri et al. (2002), Mangan and Sisson (2000), and Brooker et al. (1999) (see Supplemental1 materials for details). A field aperture was used to reduce backgrounds for H and C, which were monitored using either a volatile-free glass from Shishkina et al. (2010) or a piece of quartz embedded within each sample mount. Halogens were calculated using Lipari glass (Hunt and Hill 1993) as the primary calibration standard for Cl, and NIST SRM610 glass as the primary calibration standard for F. Halogens were also quantified for halogen-free experiments as a check for possible contamination. Values were checked against internal secondary glass standards and synthetic halogen-rich glasses synthesized using the starting material SH3. SIMS glass halogen concentrations were also checked and compared against EPMA.
Secondary electron microscopy (SEM)
Backscattered SEM images of polished, mounted samples were collected using a Hitachi S-3500N scanning electron microscope at the University of Bristol, with a 15–20 kV accelerating voltage and 15 mm working distance. All samples were imaged prior to SIMS analysis to identify the phases present, produce image maps for sample navigation, and locate areas of apatite and glass suitable for ion microprobe work (sufficiently large and free from cracks and inclusions). To avoid contaminating the sample surface with C in advance of SIMS analysis, samples were not C coated prior to imaging in low vacuum mode. Run products were imaged again following ion microprobe work to confirm the location of sputter craters.
We followed the calculation scheme of Ketcham (2015) for stoichiometric calculations, with formula proportions calculated on a 25-oxygen basis. We placed Mg, Mn, Fe, and Na on the Ca site, and Si onto the phosphate site. Any deficiency in P on the phosphate site was filled with carbonate where possible; any remaining carbonate was placed onto the channel volatile site together with F, Cl, and hydroxyl (Supplemental1 Table 1). Stoichiometric totals are generally good, with the Ca-site contents 9.967 ± 0.070, P-site contents 6.037 ± 0.030, and average X-site totals for the halogen-bearing experiments of 1.913 ± 0.087 (Supplemental1 Table 1), although halogen-free experiments have lower totals (see below). There is also a correlation between the measured OH and OH calculated by difference (see later discussion).
Experimental run products
Experimental run products for both starting materials typically comprise microlite-free glass + apatite, with a minority of samples also containing clinopyroxene ± fluid (see Table 2; Fig. 1). The experiments were designed to be volatile-undersaturated, because of the difficulty of constraining the composition of any fluid(s). The two experiments run at 0.5 GPa contain sparse vesicles, which may indicate that these samples had just reached volatile saturation. Apatites are large and euhedral (typically up to 100 μm perpendicular to c-axis and up to 1 mm parallel to the c-axis) and commonly contain melt inclusions that are visible in sections cut perpendicular to the c-axis (Fig. 1). Experiments run at lower pressures or higher cooling rates formed apatites with more skeletal or hopper textures.
Glasses. Experimental glasses from the “BA” experiments are Al-rich haplobasalts with ~5 wt% total alkalis, 9–10 wt% MgO, 14–16 wt% Al2O3, and 18–30 wt% CaO on an anhydrous basis (Supplemental1 Table 2). Silica contents are 44.4–49.6 wt% SiO2, normalized to 100% on an H- and C-free basis. The glasses have high volatile concentrations, as expected given the experimental run pressure of 1 GPa and nominal bulk volatile compositions (Table 2). Some CO2 was found even in the nominally C-free runs, which we attribute to infiltration of C through the Pt capsule walls during the course of the experiment (Brooker et al. 1998) or possibly incomplete decarbonation of the starting material and/or atmospheric contamination. H2O contents are in the range 0.7–7.1 wt%, and CO2 concentrations range from 300 ppm to 1.3 wt% (Supplemental1 Table 2). Halogen concentrations in the glass are 0.8–1.6 wt% F and ~0.8 wt% Cl (Supplemental1 Table 2).
The “BM” experiments formed phonolitic glasses with 57.2–61.8 wt% SiO2 and 12.6–16.3 wt% total alkalis (Supplemental1 Table 2). For the halogen-bearing “BM” experiments, halogens were added in the form of NaCl and NaF, so the melts for these experiments have correspondingly higher Na2O contents (Supplemental1 Table 2). H2O concentrations are in the range 1.3–7.1 wt% and CO2 concentrations are 1600–7100 ppm, consistent with volatile concentrations in the BA experimental glasses. Fluorine contents are also similar to those in the BA glasses (0.85–1.0 wt% F) but Cl concentrations are higher (1.25 wt% Cl) for the same nominal bulk Cl added. Glasses are homogeneous throughout each sample, with typical relative standard deviations of approximately 1.2% for CO2, H2O, F, and Cl. This is smaller than the analytical uncertainty, and we therefore used the analytical uncertainty to estimate and propagate errors in the partitioning data.
Apatites. Experimental apatites from the halogen-free BA experiments are hydroxy-apatites with 0.7–1.7 wt% H2O and a wide range of C contents up to 1.80 wt% (C expressed as CO2) (Supplemental1 Table 1). Apatites from the halogen-bearing experiments are hydroxyl-bearing fluor-apatite, with ≥2 wt% F and compositions systematically shifted to lower OH and C contents (≤0.8 wt% H2O and ≤0.22 wt% CO2, Supplemental1 Table 1). Apatites from these halogen-bearing experiments have volatile contents of F > Cl >> OH > C, even when these components were added in the same concentrations to the starting mixture (e.g., BA12, which had 1 wt% each of F, Cl, and OH in the starting material, Tables 2 and Supplemental1 Table 1). In the halogen-free experiments, the apatite H2O and CO2 contents increase with increasing dissolved H2O and CO2 in the coexisting glass, respectively, and the CO2 content increases with increasing CO2/(H2O+CO2) in the glass (Fig. 2). The same pattern is observed in the halogen-bearing experiments, but with lower overall OH and C contents as described above. Similarly, experimental apatites from the BM experiments show high H2O and CO2 contents in the halogen-free runs, (0.7–1.2 wt% H2O and up to 1.2 wt% CO2) and significantly lower concentrations in the halogen-bearing experiments, which routinely produced fluor-apatite with >2.5 wt% F (Supplemental1 Table 1). Carbon contents increase with increasing concentration of the minor elements (Mg, Na, and Si; Fig. 3).
The stoichiometry calculations suggest that, for the halogen-free experiments, there is no space on the phosphate site for carbonate, such that all the carbonate and hydroxyl are accommodated on the channel site (Supplemental1 Table 1). In contrast, for some of the halogen-bearing experiments, there is sufficient space on the phosphate site to assign some of the carbonate, with the channel site occupied by the remaining carbonate, halogens, and hydroxyl.
Minor element concentrations in the apatites are clearly related to the host melt composition. Apatites from the BM experiments typically contain higher alkalis and lower Mg compared with those from the BA experiments (Supplemental1 Table 1).
We used the experimental apatite and glass compositions to calculate the apparent Nernst partition coefficients, Di = (Ciap/Cim) where C is the concentration of element i in wt%. This representation allows the distribution of volatile species between apatite and melt to be directly compared with other literature data (in the case of H, F, and Cl), and to give the first experimentally determined partitioning data for C between apatite and silicate melts. Note that to maintain consistency with previous studies (e.g., McCubbin et al. 2015), we have calculated the partition coefficients between volatile abundances in apatite and melt as the same species, i.e., OH in apatite is calculated as the equivalent H2O content, whereas CO32– in apatite is calculated as the equivalent CO2 content, on a concentration (wt%) basis. Our calculated D values show, as expected, that F is highly compatible in apatite, with DF between 1.3 and 3.6 (average = 2.2). Chlorine is moderately compatible (DCl = 0.6 to 2.3), and OH is generally incompatible (DOH = 0.06 to 0.97; average = 0.27) (Supplemental1 Table 3), although its compatibility varies with a bulk mixed volatile content. DCO32- is variable, with values ranging from 0.05 to 2.1. Notably, CO32– was actually compatible in apatite in several of the halogen-free experiments. Both DCO32- and DOH are significantly higher in the halogen-free runs.
According to the strict definition of these distribution coefficients, the volatile components should be calculated using activity (or mole fraction if assuming ideal behavior). However, it is not obvious that this approach brings greater clarity to the results of these experiments. In particular, the high pressures and range of melt compositions used means that there is some considerable uncertainty concerning the validity of models describing the distribution of dissolved water and C species in the melt (e.g., Brooker et al. 1999; Sowerby and Keppler 1999; Morizet et al. 2002; Hui et al. 2008), even if the apatite behavior is ideal at high pressure and temperature (see Li and Hermann 2017 for a discussion). For completeness, we give apatite-melt KDOH-Cl, KDOH-F, and KDCl-F in mole fraction form (Supplemental1 materials) using the same water speciation model as Li and Hermann (2017) for consistency with their approach, though this may not be the most appropriate for the range of melt compositions included. These KD values are calculated by normalizing the volatile site contents such that XOH + XF + XCl = 1, excluding carbonate (Supplemental1 materials). For OH-carbonate exchange, however, we present only KD values calculated on a concentration basis to avoid introducing errors as a result of the poorly understood variation in C speciation in silicate melts (e.g., Morizet et al. 2002).
From our experiments, the resulting distribution coefficients (calculated following McCubbin et al. 2015 as the ratio of partition coefficients) are KDH2O-F = 0.023–0.09, KDH2O-Cl = 0.07–0.11, and KDCl-F = 0.27–0.98 (Supplemental1 Table 3). Apatite-melt distribution coefficients for H2O-CO2 exchange are defined more rigorously in Figure 4 through logKDH2O-CO2 = logDH2O – logDCO2, where logKD is the intercept. This gives KDH2O-CO2 = 0.355 ± 0.05 for the “BM” experiments and 0.629 ± 0.08 for the “BA” experiments (uncertainties represent a 95% prediction interval). This suggests a dependence on the melt major element composition, with systematically higher KD values (as calculated for individual experiments) in the BM system (Fig. 4). The gradient in Figure 4 is approximately 0.65 for both the BM and BA experiments, whereas for an ideal system it should be equal to 1.0. This suggests that C-H partitioning may be non-ideal for high-temperature igneous apatites, which would be consistent with the development of significant vacancy concentrations in the more carbonate-rich apatites (see below).
CO32– in apatite
Our primary focus was to define the carbonate partitioning behavior between hydroxyl-bearing apatite and hydrous silicate melt. The apatites themselves contain quite high carbonate concentrations, typically several hundred to a few thousand parts per million, even in the halogen-bearing experiments. This is in contrast with natural silicate melts, which commonly record magmatic volatile concentrations only after significant degas-sing of CO2, either into a fluid phase or during post-entrapment modification and formation of a shrinkage bubble, resulting in lower CO2 contents of typically a few hundred parts per million (Wallace 2005; Blundy et al. 2010; Hudgins et al. 2015; Tuohy et al. 2016; Maclennan 2017). The KD values for OH-carbonate exchange (KDH2O-CO2) appear to be dependent on the melt major element composition, with higher values in the BM experiments than in the BA experiments (see Fig. 4; Supplemental1 Table 3). In contrast, the apparent carbonate-halogen exchange coefficients are very low, with KDCO2-Cl < 0.17 and KDCO2-F < 0.11 (Supplemental1 Table 3). To the best of our knowledge, these are the first experimental constraints on carbonate partitioning in igneous apatite, so we are unable to compare our data with those of other studies. The advantage of SIMS analysis is that the total C concentration is technically easy to measure in situ on unoriented grains, although it cannot provide structural information related to site occupancy, which requires techniques such as FTIR, XRD, or NMR (e.g., Fleet 2017).
Incorporation of CO32– in experimental igneous apatites
Apatite data from our halogen-free experiments indicate that the Type A substitution mechanism is the dominant one for the carbonate anion. Both the carbonate and OH contents of apatite vary systematically with increasing CO2/(H2O+CO2) in the host melt (see Fig. 2). This indicates that the apatite carbonate concentrations are directly linked to the volatile composition of the melt. Since OH is well known to occupy the channel site, this indicates that carbonate is also incorporated into the channel site. The stoichiometry calculations also indicate that there is insufficient space on the phosphate site to accommodate any significant Type B carbonate, and therefore the carbonate should sit on the X-site (Type A; see Supplemental1 Table 1). This has been confirmed using FTIR (see Supplemental11 Fig. 1) where the positions of the carbonate ν3 vibrational peaks are consistent with dominantly A-site occupation (e.g., Fleet et al. 2004; Fleet 2017). However, while OH calculated by charge balance in the channel site is equivalent to measured OH in the most OH-rich samples, for samples with higher carbonate contents the measured OH is significantly lower than OH calculated by charge balance (Fig. 5). This suggests that the incorporation of carbonate into igneous apatite at high temperatures may involve the creation of vacancies, significantly greater than the number of OH- vacancies predicted to charge balance CO32– via Equation 2. The presence of structural H2O in the channel site (e.g., Mason et al. 2009; Yoder et al. 2012) seems unlikely given the high run temperatures of the experiments.
In fact, the under-occupancy of the X-site suggests the formation of a significant “oxyapatite” component, with O2– (and a vacancy) substituting for 2OH- within the channel site (Trombe and Montel 1978; Young et al. 1981; Schettler et al. 2011). First-principles calculations support the idea that significant defects on the channel site can be formed at high temperatures (>1000 K), including the formation of oxyapatite coupled to OH- vacancies, resulting in significant non-stoichiometry at high temperatures (Matsunaga and Kuwabara 2007; Kubota et al. 2014). This deviation from stoichiometric mineral formulas is consistent with our interpretation that C-H exchange is non-ideal.
Our observations are also consistent with experiments that resulted in the formation of Type A carbonate apatite by the reaction of hydroxyapatite with dry CO2 (Bonel 1972); and with first-principles calculations that indicate a greater stability of the Type A substitution at high temperatures (Kubota et al. 2014). The lack of negative correlation between CO32– and Ca or P also argues against a significant B-type substitution (De Maeyer et al. 1993). However, the highest total carbonate contents are also associated with high minor element concentrations (e.g., Mg, Na), which suggests a subsidiary Type B substitution similar to Equation 5 or 6. Peroos et al. (2006) showed that although the Type A substitution was energetically favorable, a Type B substitution, charge balanced by Na+, was also favorable when Type-A carbonate was already present.
In contrast, the stoichiometry of apatites from our halogen-bearing experiments suggests the additional formation of some B-type carbonate apatite. In some of these apatites, the phosphate site has enough space to accommodate some carbonate, and the channel site incorporates the remainder plus halogens and OH (Supplemental1 Table 1). In contrast with apatites from the halogen-free experiments, there is good agreement between OH contents calculated by difference and measured OH for the halogen-bearing experiments (Fig. 5). This suggests that these calculated site assignments are reasonable, and consistent with calculations showing that at high temperatures the Type A carbonate substitution should be more stable than Type B (e.g., Kubota et al. 2014). However, we suggest that in the presence of abundant halogens, the formation of F-Cl-OH apatite is the most energetically favorable, and that carbonate can be shifted onto the phosphate site.
OH-Cl-F distribution between apatite and silicate melt
The OH-F-Cl apatite-melt exchange coefficients calculated from our experimental data are consistent with those of other studies, but with some significant differences. There are only two other experimental Cl-OH-F apatite-melt partitioning studies with direct measurements of all channel site components. The extended abstract by Potts et al. (2015) reported experiments conducted at 1 GPa and 1350–1450°C with a composition similar to the mesostasis of lunar basalts, while McCubbin et al. (2015) performed apatite-melt experiments at 1–1.2 GPa and 950–1000°C using an Fe-rich basalt. Our calculated nominal DF, DCl, and DOH are within the range reported by these and other previous studies (Fig. 6; Table 3). This includes experiments without direct measurement of OH, for which we calculated nominal DOH “by difference” (see Table 3; Doherty et al. 2014, rhyodacite at 50 MPa, 850–950°C; Webster et al. 2009, rhyodacite at 200 MPa, ~900°C; Mathez and Webster 2005, basalt, 1050– 1150°C; Webster et al. 2017, rhyolite at 50–200 MPa and 700–1000°C; and Li and Hermann 2015, 2017, “pelite” melts at 2.5–4.5 GPa and 600–900°C). This was done assuming a stoichiometric channel site containing no carbonate (see earlier discussion) and calculating H2O(m) by difference where necessary. These “by difference” calculations are subject to a significant uncertainty (e.g., Devine et al. 1995; Humphreys et al. 2006), and the direct analysis of all volatile components in both melt and apatite is strongly encouraged for future work. The data set also includes a mixture of volatile-saturated and volatile-undersaturated experiments (see Table 3), and at least some of the volatile-saturated experiments are rich enough in Cl that fluid immiscibility is likely (e.g., Webster et al. 2017). These results, perhaps not surprisingly, are strongly scattered and cover a wide compositional range (Figs. 6–8). The variation in starting materials and experimental conditions suggests that some of this variability may be due to the effects of changing melt composition or pressure and temperature. This is supported by a systematic decrease in both DF and, to a lesser extent, DCl, with increasing temperature and increasing melt CaO content in the compiled literature data set. Increasing experimental pressure causes only a minimal decrease in DF,Clap-m.
We compared these results with earlier thermodynamic expressions derived by Piccoli and Candela (1994) for the system apatite-fluid. Their KDap-fl were calculated using the thermodynamic data of Zhu and Sverjensky (1991) to give the fugacity ratio for the coexisting aqueous fluid, with aqueous species data derived from Robie et al. (1978) and Stull and Prophet (1971). High-temperature values for KDOH-Cl are up to an order of magnitude lower for the apatite-fluid than for the apatite-melt KD exchange data, but there is better agreement between the two systems at low temperatures (Fig. 8). There is also agreement on the direction of change of KD with temperature (cf. Li and Hermann 2015). In contrast, the values for KDOH-F are 2–3 orders of magnitude lower for apatite-fluid (Piccoli and Candela 1994) than for apatite-melt (literature data compilation, Fig. 8). The cause of this mismatch for KDOH-F is unclear, particularly given that there is relatively good agreement for KDOH-Cl at low temperatures (where one or more fluid phases are most likely to be present). Calculating KD values using OH and halogen mole fractions instead of H2Ot results in higher values in Figure 8. The experiments do not contain any other phases that could incorporate significant F. Our calculations (together with those of the other studies in the literature) were done using melt F concentrations instead of activities, and fluoride activity varies with both melt composition (e.g., Scaillet and Macdonald 2004) and temperature (e.g., Webster 1990). Piccoli and Candela (1994) attempted to apply their method to the Bishop Tuff and found similar problems, with good agreement between predicted (from apatite) and measured (from melt inclusions) Cl concentrations, but a much wider discrepancy for F, which they interpreted as a problem with the assumption that F is present only as HF in the fluid. We therefore suggest that improved fluoride activity and speciation models for silicate melts and fluids may help to resolve this problem.
Recent experimental studies of apatite–melt partitioning have greatly enhanced the potential of apatite as a tool for interpreting magmatic volatile contents, in both terrestrial and planetary settings (Piccoli and Candela 1994; Boyce and Hervig 2008; McCubbin et al. 2015). The results presented here extend this work to the important magmatic volatile C, which records key information regarding deep magma storage and early degassing processes. Our new partitioning experiments on haplobasaltic andesite and trachyte melts provide the first constraints on partitioning mechanisms and exchange coefficients for C in high-temperature igneous apatite. Stoichiometry calculations and preliminary FTIR-ATR analysis indicates that carbonate is accommodated primarily in the c-axis channel in our experiments. OH calculated by difference agrees relatively well with measured OH for the halogen-bearing experiments but is systematically low for the halogen-free experiments. This suggests the presence of a significant oxyapatite component at high temperatures, and emphasizes that calculations of OH by difference should be treated with care. Analysis of C in apatite represents a potential new route to better understanding the original CO2 contents of melts, particularly in arc systems, where melt inclusion CO2 concentrations likely represent a significant underestimate of CO2 in the un-degassed melt. The ease of SIMS analysis, as demonstrated here, should facilitate this goal, particularly for small natural crystals and inclusions within phenocrysts. We encourage future work comparing CO2 in arc melt inclusions with CO2 inferred from coexisting apatite inclusions, and suggest that this may help to improve our understanding of volatile fluxes at subduction zones.
Regression of our new partitioning data, alongside previously published experimental data in the system apatite–silicate melt, shows that while measurements of Cl–OH exchange are in good agreement with existing estimates for the system apatite–fluid (Piccoli and Candela 1994), there is a large discrepancy for F–OH exchange, which may be due a to relatively poor understanding of the fluoride activity and speciation in silicate melts and fluids. This highlights the need for further experimental work focused on clarifying the mobility and compatibility of halogens between solids, melt, and fluids close to the magmatic-hydrothermal transition. Nonetheless, the current study marks a significant advance in the understanding of volatile partitioning in high-temperature igneous apatites and opens up the potential for quantitative analysis and modeling of magmatic volatile systematics in both terrestrial and extraterrestrial environments. Apatite can accommodate the full range of volatile elements and, in our view, future work should focus on the quantitative modeling of variations in apatite composition during common igneous processes such as cooling, ascent, and degassing of fluid(s), with the aim of fully developing apatite as a tool for investigating magmatic storage and degassing processes.
This project was funded by the Natural Environment Research Council under grants NE/K003852/1 and NE/K004786/1, as well as multiple visits to the NERC ion microprobe facility at University of Edinburgh. M.C.S.H. was supported by a Royal Society University Research Fellowship. We are grateful to Stuart Kearns for analytical support for the electron microprobe, and to Francis McCubbin and Victoria Smith for useful discussions. We acknowledge Bernie Wood and Andrew Matzen for access to the high-temperature gas-mixing furnace at University of Oxford, and Niccy Potts for access to her unpublished experimental distribution coefficients. We thank Francis McCubbin and Adam Simon for journal reviews that helped to clarify the manuscript, and Dan Harlov for his editorial contributions. Finally, M.C.S.H. is grateful to Tom Sisson and Tim Grove for, in a previous decade, encouraging a study of volatiles in apatite.