Macro- and micro-perthitic microclines from pegmatites from Perth, Ontario (Wards catalogue 46 E 0510) and Keystone, South Dakota (Wards 46 E 5125) have been studied using light and electron microscopy. A sample of the type perthite from Perth, Ontario (Hunterian Museum, Glasgow, M2361) was compared using light microscopy. It differs in bulk composition and microtexture from the Wards sample. The Perth sample from Wards is a mesoperthite, with sub-periodic ~mm-thick albite veins near (100), with irregular surfaces. The microcline has regular tartan twins and formed from orthoclase by a continuous process. The Keystone sample is a microperthite, with non-periodic albite veins mainly in {110}. Irregular tartan twins, volumes of irregular microcline and subgrains suggest that the microcline formed by dissolution–reprecipitation. Microcline in both samples contains semicoherent cryptoperthitic albite films that formed after the development of tartan twins. The bulk compositions of these intergrowths imply exsolution below ~400°C. Diffusion parameters imply sustained heating for between 0.11 My at 400°C, 1.5 GPa and 8.4 My at 300°C, 1 GPa. Unrealistic times are required at 200°C. Subsequently, the crystals reacted with a fluid leading to replacive growth of the vein perthites. Unusually, Albite twin composition planes in replacive subgrains have sub-periodic dislocations, formed by coalescence of advancing growth twins. Processes that might lead to periodic, replacive intergrowths are discussed. The Perth and Keystone feldspars have been used for experimental work on dissolution during weathering and on anomalous thermoluminescence fading. Their microtextures make them unsuitable for obtaining properties that can be extrapolated to feldspars in general.

Alkali feldspars are a common and striking constituent of granitic pegmatites. Perhaps because they often form crystals 100s of mm across they have been little studied at the sub-μm scales accessible by Scanning (SEM) and Transmission Electron Microscopy (TEM). In this paper we present a study of microtextures in three pegmatitic alkali feldspars (microcline), two from near Perth, Ontario and one from Keystone, South Dakota, at mm to sub-μm scales. One sample, (M2361), was kindly supplied by the Hunterian museum, Glasgow, and is believed to be part of the type specimen of perthite (named by Thomson, 1843) from Otty Lake near Perth. It can be seen by the unaided eye to be a mm-scale intergrowth of sinuous lamellae of two feldspars, one a deep reddish brown, the other a lighter shade of pink. It was only investigated using light microscopy in this work. The second Perth sample, which is a stronger pink colour in hand specimen, and less obviously perthitic, was sold by Wards (catalogue 46 E 0510) as perthite from Perth. The Keystone sample was also supplied by Wards (catalogue 46 E 5125).

One or both of the Wards samples have been used in experimental studies related to mineral weathering, by Holdren and Speyer (1985, 1987), Stoessell and Pittman (1990), Anbeek (1992), Hodson et al. (1997), Hodson (1998) and Brantley and Mellott (2000). Rogers and Bennett (2004) used Keystone microcline to study the role of micro-organisms in the release of nutrients from silicates. The feldspars have also been used in work on anomalous thermoluminescence (TL) fading by Baril and Huntley (2003), Meisl and Huntley (2005) and Godfrey-Smith et al. (2005).

Electron Microscopy (EM) methods were used to study these samples because both dissolution and TL fading are fields in which defect microstructure has an important role, although defect microtextures at the scale reported here have not been investigated previously. It was the intention of the workers in both fields that the properties established could be applied to alkali feldspars in general. We know from our own studies (Lee and Parsons, 1995; Lee et al., 1998, Hodson et al., 1997), based on feldspars of normal crystal size from granites, that crystal defects of various types are important factors in the rates and mechanisms of feldspar dissolution and mechanical degradation. As we show below, the microtextures of these pegmatitic feldspars are extremely complex, vary from point-to-point in the samples, and are different in several ways to the types of alkali feldspar common in normal igneous rocks.

A second aim was to investigate the processes producing the perthitic intergrowths and to explore the potential of using feldspar microtextures at the EM scale to understand the geological history of pegmatites. Coherent cryptoperthitic albite lamellae occur in both microclines and we show that their character and periodicity are consistent with existing experimental work on perthite exsolution kinetics by volume diffusion (Yund, 1974; Yund and Davidson, 1978), extrapolated to the range 400–300°C. The cryptoperthitic microcline is cut by periodic lamellar micro- and macro-perthitic intergrowths at up to mm-scale that could not have developed, on realistic geological timescales, by a continuous diffusional process. Microtextures at the EM scale clearly show that the coarse perthites are formed by replacement. We discuss possible explanations for their periodic character.

Smith (1974, Chapter 19) and Smith and Brown (1988, Chapter 19) provide a summary of early work on coarse perthites, many from pegmatites, with numerous light micrographs. Cerný (1994) provides a comprehensive review of the chemical and textural properties and geological relationships of alkali feldspars from pegmatites. These sources illustrate the daunting variety of microtextures visible using light microscopy (LM). Cerný (1994) shows examples of feldspar with coexisting film and vein microperthites, including a sample from near Otty Lake near Perth, Ontario (his fig. 14D) which is probably the same as the Wards sample described here. Laves and Soldatos (1963) include a micrograph ofa (010) section of a perthite from Perth, (reproduced by Smith, 1974, fig 19-4) which shows both microperthitic μm-scale film lamellae and mm-scale macroperthitic lamellae and lenses in the microcline matrix, with a small angular difference between them. This too is similar to the Wards specimen. The microperthitic lamellae are in the ‘Murchison plane’, a non-integral plane between (6İ01) and (8İ01), the macroperthitic lamellae are in (100).

The first thorough systematic studies of perthites from pegmatites, using light microscopy, were by Andersen (1928), who studied alkali feldspars from 300 Norwegian pegmatites, noting that many contained microperthitic lamellae lying in the ‘Murchison plane’. Modern work has shown that such lamellae, with thicknesses typically of ~1 μm, are fully- or semi-coherent. Willaime and Brown (1974) showed that they lie in the plane of minimum coherency strain energy. Andersen (1928) called microperthites with this orientation ‘film perthite’, the terminology we use here. Film lamellae of these dimensions form by volume diffusion. The coarsest coherent film lamellae reach ~10 μm in thickness, in granulite-facies rocks. See Parsons and Brown (1991) and Brown and Parsons (1993) for reviews.

Alling (1921, 1932, 1938) stressed the textural differences between feldspars from pegmatites and those in common plutonic rocks. He recognized that many perthites form by replacement, and distinguished ‘deuteric’ (involving late fluids in a closed magmatic system) and ‘hydrothermal’ types (fluid introduced from an external source). He attempted to classify the different morphological types but did not give information on their crystallographic orientation, a vital aspect of any description of an intergrowth. A guide to characterizing intergrowths is provided by Parsons et al. (2015). Soldatos (1962) and Laves and Soldatos (1962, 1963), studied feldspars from pegmatites using single-crystal X-ray diffraction (SXRD). MacKenzie and Smith (1962) included a number of samples from pegmatites in an extensive SXRD study of perthites.

Although the majority of alkali feldspars from pegmatites are turbid and have coarse exsolution microtextures, some have yielded ‘gem quality’ crystals that have been used for experimental determination of diffusion coefficients. Orthoclase from a pegmatite at Benson Mines in the Adirondacks was used by Foland (1974) to obtain the activation energy and diffusion coefficients for Ar diffusion in K-feldspars. Microtextural information about ‘Benson orthoclase’ is provided by Parsons and Lee (2005). Another important gem quality pegmatitic alkali feldspar is the yellow ferriferous orthoclase from Itrongay, Madagascar. Unfortunately there are many varieties of ‘Madagascar orthoclase’ in collections. A set of 20 samples were properly characterized by Coombs (1954), who discovered a considerable range in composition and structural state. Parsons and Lee (2005) summarize the variation in this material, and provide TEM images of very fine-scale exsolution and tweed microtextures in one example, used by Arnaud and Kelly (1997) and Wartho et al. (1999) for work on Ar diffusion. Keefer and Brown (1978) used TEM in a crystal-structural study of a cryptoperthite from a pegmatite from Rabb Canyon, New Mexico. These crystals were cooled rapidly from elevated T and have not experienced the relatively extended cooling and fluid-feldspar reactions usual in granitic pegmatites. White and Barnett (1990) used TEM to study twinning in extremely pure microcline in the Hemlo, Ontario gold ore body but the original grain size is sub-mm.

Very few studies of ordinary ‘garden quality’ pegmatitic feldspars have been undertaken using SEM and TEM methods and all have concentrated on specific aspects of the feldspar microtextures. Aberdam (1965) carried out pioneering work on the relationship between dislocations and exsolution lamellae. Fitz Gerald and McLaren (1982) investigated Albite and Pericline twinning in microcline from several pegmatites and Sheets and Tettenhorst (1997) studied replacement of pegmatitic feldspar by clay minerals. Sánchez-Muñoz et al. (1998) studied six adularia crystals from Alpine veins using high-resolution TEM (HRTEM) and nuclear magnetic resonance spectroscopy, confirming that they have the coherent tweed domain microtexture characteristic of orthoclase (Eggleton and Buseck, 1980). Sánchez-Muñoz et al. (2006) used cathodoluminescence (CL) and SEM imaging to characterize twinning and exsolution features in a ‘giant’ microcline from the Golconda pegmatite, Minas Gerais, which has both macroperthitic veins and microperthitic film lamellae. Sánchez-Muñoz et al. (2008) studied the orthoclase–microcline transformation in a K-feldspar from a granite pegmatite from Lavra do Fermín, Minas Gerais, using LM. The crystal has very coarse lenticular albite lamellae on scales of 100s of μm set in a predominantly orthoclase matrix, and long-range strains induced by Albite twins in the albite lamellae have led to the development of Albite and Pericline twinned microcline in the adjacent orthoclase matrix. It would be valuable to study this process at the TEM scale. Sánchez-Muñoz et al. (2012) provide LM and TEM micrographs of feldspars from a large number of pegmatites including some beautiful LM images of twinning in microcline, and HRTEM images illustrating the coherency of twins and albite films. Bright-field TEM images of fine-scale film lamellae show features in common with lamellae from the Shap granite, including, in our view, evidence that they have been modified in some cases by fluids (Lee et al., 1995; Lee and Parsons, 1997) but Sánchez-Muñoz et al. do not cite the Shap work and have reached several erroneous conclusions, which we discuss later.

Balić-Źunić et al. (2013) studied two samples of mesoperthitic feldspars from pegmatites associated with the Larvik syenite, from the Oslo province, Norway. Their SEM images show that one sample is a submicron-scale coherent film or ‘braid’ perthite, while the second is a ragged vein perthite on scales of 100 μm. The authors mistakenly interpret the difference in scale as being caused by differences in cooling rate, but the coarse intergrowth has been clearly produced by deuteric dissolution–reprecipitation. As we discuss later, intergrowths on 100 μm scales cannot be produced by diffusion. A detailed analysis of Balić-Źunić et al.'s paper is given by Parsons et al. (2015). An LM example of partial deuteric coarsening of a feldspar from a larvikitic pegmatite was given by Parsons (1978, fig. 3). Some SEM images of the intergrowths in the present study were provided in a review by Parsons and Lee (2005). Here we develop our interpretation more fully in the light of new TEM work.

We follow the conventions of Smith and Brown (1988). The abbreviations Ab, Or and An denote the feldspar components NaAlSi3O8, KAlSi3O8 and CaAl2Si2O8. The words albite, orthoclase and microcline refer to phases, not necessarily of end-member composition. The word orthoclase denotes an Or-rich feldspar phase with incomplete Si, Al order and a ‘tweed’ microtexture, monoclinic using X-ray and electron diffraction (although diffraction spots may be streaked). Microcline is more ordered, is triclinic in diffraction, and shows Albite and Pericline twinning combined in various ways usually described as ‘tartan’ twinning (Smith and Brown, 1988, p. 541). This is sometimes the variety called ‘irregular microcline’ by Bambauer et al. (1989). Orthoclase and microcline often occur together within ‘single crystals’, sometimes with sharp interfaces (e.g. Waldron et al. 1993, fig. 2), sometimes with gradational boundaries (e.g. Fitz Gerald and McLaren 1982, fig. 11). Names of twin laws are capitalized. Miller symbols of planes and forms all relate to the macroscopic C2/m symmetry of the crystals, not to the C1İ symmetry of twins in the albite and microcline phases. The composition plane of Albite twins in both albite and microcline is (010), that of Pericline twins is an irrational plane parallel to b, about which it rotates depending on feldspar composition and Si, Al order. In low microcline it is almost at right angles to (001) and in low albite almost at right angles to (100). All micrographs in this paper are of sections approximately parallel to the (001) cleavage, so that microcline shows ‘tartan’ twinning, while only Albite twins are visible in albite. The low-T variety of albite with the {110} habit is called pericline (not capitalized). The equivalent K-feldspar is adularia. Sub-grains with the adularia or pericline habit are characteristic of replacement in feldspars (Worden et al., 1990; Walker et al., 1995; Parsons and Lee, 2009; Parsons et al., 2013). The terms macro-, micro- and crypto-perthite refer to intergrowths which are visible unaided, in a light microscope, and below the resolution of a light microscope, respectively, usually in conjunction with Andersen's (1928) ‘film’ and ‘vein’ terminology. The terms perthite, mesoperthite and antiperthite, which reflect the bulk composition of the feldspar, are used as suggested by Parsons (2010, fig. 1.3).

Perthites formed by replacement are usually several orders of magnitude coarser than film perthites (Parsons and Brown, 1984). Both types of intergrowth occur in the feldspars described here. Replacement perthites are morphologically irregular. If the albite:K-feldspar ratio is high they may have a ‘patch’ morphology viewed from near the normal to (001) (e.g. Worden et al., 1990; Parsons and Lee, 2009) but crystals with more K-feldspar usually contain ragged sheets, or lenses of variable aspect ratio, with irregular surfaces orientated overall near (100) or {110}. Andersen (1928) called these ‘vein perthite’.

Turbidity in alkali feldspars is caused by large numbers of μm-scale micropores that form at the junctions between the incoherent subgrain mosaics of which replacement perthites are composed (Worden et al., 1990; Walker et al., 1995). Some replacive perthites form from coherent film perthite by replacement that is isochemical with respect to the main feldspar components in the bulk crystal and is driven by decrease in coherency strain energy. This process was called ‘mutual replacement’ by Smith and Brown (1988). The mechanisms of mutual replacement in feldspars from the Klokken syenite intrusion have been studied in detail at the EM scale by Worden et al. (1990), Walker et al. (1995), Parsons and Lee (2009), Parsons et al. (2009, 2013). Recently, Norberg et al. (2013) have for the first time successfully produced coarse patch perthites from a coherent cryptoperthitic intergrowth in the laboratory. They reacted a synthetic cryptoperthite with ~20 wt.% water or 0.1 M HCl at 1 and 1.5 GPa at up to 500°C for 4 days. Replacement was not observed in runs at 200 and 400 MPa. Although the amount of fluid used and the P in these experiments are higher than is likely in many natural circumstances, the similarity between the experimental microtextures and natural patch perthites is striking.

Replacement is often not isochemical but in coarse replacement perthites laborious electron microprobe (EPMA) traversing is needed to establish whether an original bulk composition has been retained (e.g. Brown et al., 1983). Replacement that is not isochemical with respect to the major feldspar components in the bulk crystal was unambiguously demonstrated in feldspars from the Shap granite (Lee and Parsons, 1997), and we show below that the same conclusion can be reached for Perth and Keystone.

Polished thin sections of all of the samples were characterized by LM (Figs 1, 2, 15a). The Wards samples were examined using a Philips XL30 CP SEM operated at 20 kV. Images were formed using secondary electrons (SE), backscattered electrons (BSE) and CL detectors. Specific areas of the crypto- and micro-perthitic microcline matrix in the Perth sample were analysed chemically using a Cameca Camebax electron probe operated at 15 kV. The electron beam was rastered over 10 μm squares to minimize Na loss and to provide bulk analyses of cryptoperthitic regions, and datawere quantified using an on-line PAP correction procedure. The albite lamellae included in these analyses are of variable and irregular distribution (Figs 4, 7, 17) and the size of the rastered areas relative to the lamellae accounts for the large standard deviation given in Table 1. The mean analyses given are likely to represent a good estimate of the local bulk composition of the microcline before coherent exsolution occurred.

To characterize microtextures at scales between BSE SEM and TEM imaging, (001) cleavage fragments were etched with HF acid vapour as described by Waldron et al. (1994), and examined using SE in the SEM. Etching is a useful method for distinguishing Or-rich feldspar from albite (Or-rich feldspar etches more rapidly) and for revealing dislocations and nanotunnels (Fitz Gerald et al., 2006) which etch to form discrete pits. Selected areas were prepared for TEM by gluing copper discs with a central hole 0.4–0.8 mm in diameter to the surface of the thin sections. The discs were then extracted and ion thinned until electron-transparent using an Atom Tech 700 thinner. The thinned foils were examined using a Philips Biotwin TEM operated at 120 kV.

Two of the samples of the pegmatitic alkali feldspars described here were acquired from Wards Scientific. As we note in the Introduction this is because they have been used previously in work on feldspar dissolution and anomalous TL fading. The sample of ‘Perth perthite’ (Wards catalogue 46 E 0510) comes from near Perth, Ontario, Canada and ‘Keystone microcline’ (Wards 46 E 5125) is from the Black Hills, South Dakota, USA. Because these feldspars were purchased their exact geological setting is unknown, although the size of the fragments (several cms) demonstrates that they are from pegmatites. For brevity we refer to these samples as Perth and Keystone. Perth has a vivid pink colour and is perthitic to the unaided eye, in shades of pink. It is cut by narrow bands of quartz. A colour photograph was given in Parsons and Lee (2005, fig. 7c). Holdren and Speyer (1987) determined the bulk chemical composition of three different grain sizes of powders of Perth and Keystone obtained from Wards (Table 1). The bulk composition of Perth is Or57.4Ab42.0An0.6 (Table 1). It is therefore strictly a microcline macromesoperthite.

Keystone is overall white in colour, with clear areas transected by turbid bands, many of which are approximately parallel to {110}. It is not visibly perthitic in hand specimen and is a microcline microperthite, bulk composition Or78.3Ab20.7An1.0, (Table 1). An informative description of pegmatites in the Keystone district was given by Orville (1960).

The matrix microcline in both Perth and Keystone is itself cryptoperthitic. Electron probe analyses of the macro- and micro-perthitic replacive albite, and of the bulk composition of the microcline matrix with its included micro- and crypto-perthitic albite lamellae, are given in Table 1. We presume that both samples grew as sanidine, and passed through a stage when a tweed orthoclase texture developed, before ordering to microcline, although there is no direct evidence for this. The character of the orthoclase–microcline transition is discussed by Smith and Brown (1988), Brown and Parsons (1989) and Carpenter and Salje (1994).

Perth, Ontario, is the type locality of perthite (Thomson, 1843; Hunt, 1851) and we have compared Wards catalogue 46 E 0510 from Perth with a large cleavage fragment of feldspar (Hunterian M2361) which is believed to be from the type perthite. It is likely that the much-employed Wards material comes from the same general locality as the type perthite, but it is not identical to M2361. This was discovered by Dr. James Wilson, who was born in the village of Douglas, in Lanarkshire, Scotland. Wilson graduated as a medical doctor from Edinburgh University in 1818, immigrated to Canada and settled in the village of Lanark, Ontario, moving shortly after to Perth. An enthusiastic amateur mineralogist and geologist, he sent his sample to Thomas Thomson, Regius Professor of Chemistry at Glasgow University, who gave it the name ‘perthite’ (Thomson, 1843). The local museum in Perth has a display of the type material and an account of Wilson's work. M2361 is a darker colour than the Wards material and it can be seen more easily by the unaided eye to be a mm-scale intergrowth of two feldspars, in roughly equal proportions. The matrix material is deep reddish brown, and contains somewhat sinuous lenses, parallel to b, of a second feldspar, in a lighter shade of pink. Unfortunately, confusion was introduced by Thomson, who described his sample as white in colour and consisting of “…a mass of crystals so united together as to form a kind of tessellated pavement”. His analysis showed no potassium or sodium, but consisted of 76 wt.% silica, 11.75% alumina and 11% magnesia!

T.S. Hunt, Chemist and Mineralogist to the Geological Survey of Canada, realized that Thomson's work was unreliable “owing to an unfortunate want of precision in his mineralogical descriptions” and re-described the perthite from Perth (Hunt, 1851). His sample was “light flesh-red, alternating with reddish or pinchbeck brown, the two colours forming bands from half a line to a line in width, coincident with one of the planes T, often however interrupted and intermingled one with another. The darker bands on the cleavage surface T exhibit, when viewed perpendicularly, a golden reflexion like the variety known as aventurine felspar”. This description applies in all respects to our fragment of M2361.

In thin section (not available to Hunt) M2361 is a vein perthite with albite forming periodically distributed lenticular sheets, overall parallel to b (Fig. 1a), but locally slightly oblique (Fig. 1b). At low power, lamellae appear relatively smooth-sided (Fig. 1a), although in detail the interfaces are serrated (Fig. 1b). The surfaces of the lenses lack the extreme complexity of the albite veins in Wards 46 E 0510 (Figs 2b, 3). The average periodicity of the lenses is ~0.5 mm. The albite has a pronounced {110} cleavage (Fig. 1a), and in places a second feldspar, presumably microcline, forms thin{110} plates partially outlining albite subgrains (Fig. 1b). In some regions the lenses adopt a more nearly equidimensional, globular shape, and there are also regions in which thick albite lamellae are missing. Fine-scale, film microperthite occurs in these regions. Most of the microcline has very regular, straight-sided tartan twinning (Figs 1b,c), with occasional regions of coarser twinning. It forms a matrix to the albite films, and is crowded with tiny euhedral plates of orange-brown biotite, most abundant in the central parts of the microcline lamellae (Fig. 1b). This suggests that the formation of biotite was related to the replacement process that produced the macroperthite. The plates of biotite have no visible effect, at the LM scale, on the tartan twinning (Fig. 1c). The biotite presumably accounts for the dark brown colour of the microcline in this sample and also the golden schiller noted by Hunt and visible in our fragment. The albite has fine-scale Albite twinning, varying in thickness, and sometimes showing lateral off-sets suggesting deformation or the presence of subgrains.

Hunt's two analyses (1851) correspond with a bulk composition of Or41.2Ab55.5An3.4 (Table 1), more albitic than the Ward's sample; the proportions of the phases in thin section suggest a predominance of albite. We conclude that although they are likely to have come from the same general locality, the Wards sample described in the present paper is not the type material.

In thin section, Perth (Wards catalogue 46 E 0510) is a macromesoperthite composed of ragged veins, lenses and patches of Albite-twinned albite, up to a few mm in width, enclosed within microcline with very fine-scale (~1 μm) regular cross-hatched twinning (Fig. 2). The microcline contains micro- and crypto-perthitic film albite lamellae typically ~200 nm thick (Figs 2, 3, 4, 5, 6, 7, 8 and 9). The bulk composition given by Holdren and Speyer (1987) (Or57.4Ab42.0An0.6,Table 1), has more An than either the bulk composition of the micro-perthitic microcline or the composition of the macroperthitic albite veins obtained using EPMA (Table 1). This suggests that Holdren and Speyer's powders contained small amounts of a Ca-bearing impurity, perhaps carbonate. Nevertheless their analysis of a crushed bulk sample is a reliable estimate of the bulk composition of the whole intergrowth. The albite forms veins predominantly parallel to (100), but with complex surfaces. Irregular patches also occur, and albite areas are sometimes visibly composed of subgrains (Fig. 2a). The microcline is mostly non-turbid in both samples, but the microperthitic film lamellae are often relatively turbid, making them more prominent under light microscopy. BSE images (Fig. 3) show remarkable, complex boundaries to the macroperthite, and the contrastingly regular microperthite lamellae in the microcline matrix. For reasons given below we believe that the macroperthite formed by large-scale replacement, and the fine-scale microtextures by diffusion. The latter are described first.

Perth: crypto- and micro-perthitic microcline

The microcline with its included crypto- and micro-perthitic albite has a bulk composition of ~Or92.8Ab7.2 (Table 1). Ca was below detection using the microprobe. SEM images of etched (001) cleavage surfaces (Fig. 4) and BSE images (Figs 3, 7) show albite exsolution lamellae with a large range of lengths, from <1 up to 100 μm and maximum thicknesses from a few nm to several μm. They are orientated parallel to b in (001) sections. A micrograph from Laves and Soldatos (1963, fig. 1, reproduced in Smith, 1974, fig. 19-4a) which appears to be of a sample similar to Wards 46 E 5125, shows that overall the macroperthite lies in ~(100), while the microperthitic lamellae lie in ~(6İ01). On etched surfaces (Fig. 4) thicker lamellae are straddled or cut by etch pits. These pits form in pairs at sites where misfit edge dislocation loops encircling the albite lenses intersect the cleavage surface, and demonstrate that the lamellae are semicoherent. Contrary to the interpretation of Sánchez-Muñoz et al. (2012, their fig. 14) dislocations develop during coherent coarsening at T well below the C2/mC1İ shearing transformation in albite, when twinning first appears (see Brown and Parsons, 1984b). Unlike the semicoherent lamellae in an orthoclase matrix imaged by Lee et al. (1995, figs 2, 3, 4) and by Fitz Gerald et al. (2006, fig. 1) the lamellae in Figs 4, 5, 6 and 7 do not have smooth surfaces. In feldspars from other localities (Fitz Gerald et al., 2006) structure around misfit dislocations has been dissolved away during fluid–rock reactions to produce nanotunnels with diameters of a few nm, and this is likely to be the case in Perth.

The TEM images show that the microcline is tartan-twinned on scales below that of a light microscope with twin thicknesses ranging from 200 to <20 nm (Figs 5,6,8). Presumably, the twins visible in Fig. 2 are regions where a preponderance of fine-scale twins share a common orientation in a ‘right-’ or ‘left’-handed sense, as suggested by Fig. 2c. The continuity of Albite and Pericline twins over long distances (>400 μm) suggests that there is no underlying subgrain microtexture. Albite exsolution lamellae (Fig. 6) have wedge-shaped ends (Brady, 1987) and are Albite twinned with a periodicity matching the local periodicity of Albite twins in the microcline. Twin periodicities in the albite are dictated by the enclosing microcline, indicating that it was already twinned when coherent exsolution began. Albite twins that form during exsolution in an untwinned matrix adjust their periodicity as coarsening proceeds, to minimize elastic strains (Willaime and Gandais, 1972 and see Brown and Parsons, 1988, for examples), but twin periodicities in the present case have been inherited clearly from an already twinned microcline precursor. This is not always the case. Sánchez-Muñoz et al. (2008, 2012) provide light micrographs of the development of tartan microcline twins forming selvages adjacent to thick lenticular albite veins near (100) in otherwise featureless K-feldspar (orthoclase?) in pegmatitic feldspars. In this case, long-range strains induced by Albite twin lamellae in albite have induced ordered regions with ‘left’ and ‘right’ orientation (twins) in an original tweed microtexture.

Locally the interface between individual albite lamellae and microcline in the Perth sample has a zig-zag form, alternately parallel to ~(130) and ~(1İ30) (Fig. 6). It is this zig-zag surface that accounts for the roughness of lamellar interfaces seen using SEM. Isolated micropores, with the characteristic {110} adularia habit (Worden et al., 1990; Walker et al., 1995) have sometimes developed (Figs 5, 6). Some of the exsolution lamellae have been partially replaced by albite which has euhedral outgrowths with the corresponding pericline habit. The sanidine–microcline transformation is usually placed at 500–480°C (Brown and Parsons 1989; Kroll et al. 1991) consistent with film exsolution at low-T (see later). The extended exsolution lamellae (up to 100 μm, Fig. 6) and the continuity of twins in microcline show that, in contrast to Keystone (see later), Perth microcline is not a mosaic of subgrains.

A few cryptoperthitic and microperthitic lamellae in BSE images have no Z-contrast with the microcline (Fig. 7, arrowed) and are marked only by lines of pores. TEM (Fig. 8) shows that these lamellae are composed of subgrains of irregular microcline with micropores at their junctions. This intergrowth, of lamellae of irregular microcline in a more-regularly tartan-twinned microcline matrix, is not strictly a perthite. Similar intergrowths were reported by Lee and Parsons (1998) in detrital igneous feldspars undergoing diagenesis. In other regions albite in small lamellae has been completely dissolved, leaving lenticular pores (Fig. 9).

Perth: vein macroperthite

The albite veins (Figs 2, 3) are orientated approximately parallel to (100), are typically ~0.6 mm wide and are spaced ~1 mm apart in the cryptoperthitic microcline matrix. The albite is of near end-member composition (~Ab99.2, Table 1). The interface of the veins with host microcline is intricately serrated owing to the development of euhedral outgrowths of albite. The complex interfaces are strongly reminiscent of the fractal Mandelbrot set (Fig. 3). The turbidity of the albite and the microcline is similar and not unusually intense, but is most pronounced near the interfaces of veins. The least turbid areas of albite have the thickest Albite twins and some non-turbid subgrains are untwinned. CL images (Fig. 10) show that the albite outgrowths are zoned, the outermost ~0.05 mm often being non-luminescent. Microcline immediately adjacent to the veins luminesces more brightly than in surrounding areas. The gradational changes in luminescence suggest a diffusion profile, perhaps in a trace element, but we do not know its source. There is no corresponding change in grey-scale in BSE SEM images (Fig. 3) when contrast depends essentially on Na and K distribution.

The albite veins are composed of slightly mis-aligned subgrains at the scale of 100s of μm (Fig. 2a). Albite twins range considerably in thickness and many are laterally discontinuous and wedge out. Some of the twins have developed from subgrain boundaries. TEM images (Fig. 11) show that Albite twins sometimes define steps in the microcline–albite interface. There is localized coherency strain and dislocation arrays along the immediate interface between albite films and microcline, which is clearly semicoherent. Similar sets of periodic dislocations were found by Norberg et al. (2011) at interfaces between albite and orthoclase produced during laboratory albitization experiments, and were reported by Lee and Parsons (1997, Fig. 4) along natural replacive albite–orthoclase interfaces in feldspars from the Shap granite.

Sub-regularly to irregularly-spaced etch pits occur on HF etched surfaces where Albite twin composition planes (010) in albite intersect the (001) cleavage surface (Fig. 12). Albite twin composition planes are usually assumed to be fully coherent but clearly these are not. Some planes have many closely-spaced pits whereas others are free of pits or have a few that are irregularly and widely spaced. The triangular shape of the pits and their constant facing-direction along the twin plane shows that the dislocations are oblique to (001). Sometimes the line of pits along the composition plane has branched off and followed an oblique track into the interior of a twin (top left of Fig. 12). Unlike dislocations surrounding lenticular exsolution lamellae (Waldron et al., 1994) the dislocations do not crop out in pairs, so they do not represent sections through dislocation loops. The etch pits differ considerably in both size and shape on either side of a twin. On one side they may be relatively large and angular whereas on the other they are smaller and more rounded (Fig. 12). In both cases, however, each individual pit is symmetrical about (010). TEM images (Figs 13, 14) confirm that each etch pit has formed where highly strained crystal structure surrounding a dislocation on the Albite twin composition plane intersects the cleavage surface. In most cases the dislocations are associated with steps of a few nm in the composition plane. Some Albite twins wedge out laterally and these terminations are marked by a high concentration of dislocations (Fig. 14).

In addition to dislocation etch pits, narrow and shallow grooves occur on the etched surface of each twin (Fig. 12). Each groove is up to ~3 μm long by ~0.1 μm wide. The long axes of the grooves are orientated approximately parallel to {110}albite but are present in only one orientation within any one twin. In adjacent twinsthe grooves are related bya mirror plane on (010), forming a ‘herringbone’ structure either side of the Albite twin composition plane. The grooves terminate at, and are parallel to, the ‘leading’ edges of triangular dislocation etch pits, particularly larger ones, and grooves change direction at these points. It seems likely that the grooves result from increased dissolution in regions affected by long-range strains, but no strain contrast that could correspond with the grooves was observed in TEM images.

Keystone has a bulk composition (Table 1) of ~Or78Ab21An1, more Or-rich than Perth (Holdren and Speyer, 1987). In thin section (Fig. 15a) it is a vein microperthite with albite veins mostly in {110}, some in (100). The veins are more ragged and variable in thickness than Perth and the microperthite has no easily defined periodicity. In contrast with the regular, periodic, fine-scale tartan twinning of the Perth microcline, Albite and Pericline twins in Keystone vary considerably in thickness, reaching ~100 μm (Fig. 15a). They are markedly spindle-shaped in (001) section.

Keystone: cryptoperthitic microcline

The irregularity of the twin microtexture of the microcline is maintained at the TEM scale (Fig. 15b). In some areas the twins become diffuse and die away. Following Bambauer et al. (1989) the complex intergrowth would be described as ‘irregular microcline’. Featureless areas are probably ‘tweed’ orthoclase although tweed is not visible at the magnification used. Unlike Perth there are well-defined subgrains with the {110}–(010) adularia habit, with micropores at their junctions. Very similar microtextures occur in granites and syenites where perthite has been subject to replacive coarsening by dissolution–reprecipitation (Walker et al., 1995; Lee et al., 1995; Parsons and Lee, 2009; Parsons et al., 2013).

Like Perth, the Keystone microcline contains film crypto- and micro-perthitic lamellae (Figs 16, 17). The coarser microperthitic albite film lamellae are ~0.1–0.25 μm in thickness by ~3–20 μm in length and on etched surfaces are straddled by paired etch pits (Fig. 17a), demonstrating that they are semicoherent. The finer cryptoperthitic lamellae, <0.1 μm in thickness, are fully coherent. The Keystone film lamellae are both thinner and shorter than those in Perth, and we infer must be restricted to individual microcline subgrains. A coherent lamella could not pass across a subgrain boundary. Film lamellae post-dating subgrain formation in patch perthites have been described by Parsons and Lee (2009) and Parsons et al. (2013), and the kinetics of their formation has been discussed by Parsons and Fitz Gerald (2011).

Some of the semicoherent lamellae have been thickened by more than 10 μm by the addition of albite in the form of euhedral outgrowths with the {110} habit (Figs 17b,c). Local replacement leading to similar outgrowths is seen in the Shap granite (e.g. Lee et al., 1995; Lee and Parsons, 1997). As in Shap the Keystone late albite often contains ‘ghosts’ of the pre-existing film lamellae, and is clearly formed by replacement. Some semicoherent lamellae adjacent to fractures have been naturally dissolved, a feature also seen in Perth (Figs 6, 8).

Sánchez-Muñoz et al. (2012) provide TEM micrographs (their fig. 14) showing semicoherent film lamellae from a pegmatitic feldspar, in one case modified by development of what they call an ‘albite diamond’, that can be matched both in Keystone (Fig. 17) and in the Shap examples. However, they chose to interpret the formation of the ‘diamonds’ to be by a continuous, solid state diffusion process, and present (their fig. 21) a “schematic model for a general sequence of transformations in perthitic K-rich feldspar from granitic pegmatites” which makes no reference to replacement reactions at any stage. We think, as did Alling (1921), that microtextures formed by replacement reactions are the norm in alkali feldspars from pegmatites and plutonic igneous rocks. The pervasive character of replacement is shown most clearly by the patch perthites of the Klokken syenite intrusion (Worden et al., 1990; Parsons and Lee 2009; Parsons et al., 2013) and by our work on the Shap granite (Lee et al., 1995; Lee and Parsons, 1997). The ‘albite diamonds’ of Sánchez-Muñoz et al. (2012) are, we believe, replacive subgrains with the {110} adularia habit (e.g. present Fig. 17). This low-T growth habit is a hall-mark of subgrains produced by replacement reactions in feldspars by deuteric fluids in igneous rocks (Worden et al., 1990; Walkeret al., 1995; Lee and Parsons, 1997; Parsons and Lee, 2000, 2009; Parsons et al., 2013), during retrogression of high-grade metamorphic rocks (Waldron et al., 1993) and at near-surface T during diagenesis (Lee and Parsons, 1998). It is hard to see how ‘diamond’ albite subgrains in figure 12f of Sánchez-Muñoz et al. (2012), which are chemically zoned in the ultraviolet using CL, could have grown by solid-state diffusion. Lee et al. (2007), Parsons et al. (2008) and Parsons and Lee (2009) have illustrated and discussed the complex, sometimes oscillatory zoning that can be observed in replacive subgrains using CL.

Keystone: vein microperthite

The replacive albite lamellae (Fig. 15a) are non-periodic, irregularly distributed, turbid and very variable in size, from ~50 to 400 μm in thickness. The majority are veins at ~60 degrees to (100), close to {110}, but some veins are roughly parallel to (100). Albite in the veins is Albite-twinned and very close to end-member albite in composition (Ab99.6, Table 1). Like, Perth, etch pits occur along Albite twin composition planes, but the veins have not been examined by TEM. The veins are discontinuous and often wedge-out, and have irregular surfaces (Fig. 16), although not as complex as Perth (Figs 2, 3, 10). The microcline in their vicinity has been extensively altered to sericite (Fig. 16), and both vein and matrix contain inclusions of quartz and abundant blocky inclusions of Albite-twinned albite, a few tens of μm in size. These plagioclase inclusions have no fixed crystallographic orientation relative to the microcline.

Perth and Keystone both have two distinct microtextures: (1) a largely pristine microcline matrix, containing strain-controlled coherent and semi-coherent film micro- and crypto-perthitic albite lamellae and (2) relatively irregular, thick, largely incoherent albite veins, near (100) in Perth and predominantly near {110} in Keystone. LM work by Andersen (1928) demonstrated that these two types of microtexture commonly coexist in alkali feldspars from granite pegmatites, as they do in feldspars from granites (e.g. Lee et al., 1995).

The strain-controlled exsolution microtextures (Figs 4, 5, 6 and 7, 17a) formed during cooling by volume diffusion following nucleation at or below the coherent solvus in chemically homogeneous but tartan-twinned microcline (Figs 5, 6) with a bulk composition of Or93–94Ab7–6. Spinodal decomposition can be ruled out as an exsolution mechanism for compositions far from the solvus critical composition because the coherent spinodal is then at very low T (see discussion in Parsons and Brown, 1991). Parsons et al. (2010, their fig. 1) published a compilation of relevant binary Ab–Or solvus curves that can be used to estimate T directly because in the present case bulk An was below detection (Table 1). Because of the Or-rich bulk composition of the microcline, exsolution began at low T (see below) and this has led to film lamellae in the pegmatitic alkali feldspars that are considerably finer-scale than those typical of many granites (compare with the Shap Granite, Lee et al., 1995, bulk ~Or70). During further cooling the lamellae coarsened and misfit dislocations nucleated on the coarser lamellae to minimize coherency strain energy as the crystal structure stiffened. The development of misfit dislocations is very common in K-feldspars with fine film perthite lamellae (see e.g. Parsons and Lee, 2005; Parsons et al., 2005; Fitz Gerald et al., 2006; Parsons et al., 2013).

We can make rough, order of magnitude estimates of the Tt evolution of these semicoherent intergrowths. It must be stressed that T and kinetic estimates in this section require long extrapolations in both T and t from existing experimental work. A minimum growth T for a homogeneous microcline Or93Ab7 can be estimated by extrapolation of a strain-free solvus for equilibrium order inferred by Brown and Parsons (1984a), which at low T corresponds with an extrapolation of the strain-free ordered solvus of Bachinski and Müller (1971). The P-dependence of the solvus is known only for disordered feldspars on the strain-free solvus and is 220 K GPa−1 (Hovis et al., 1991). If the microcline grew with equilibrium order this curve implies growth at or above ~400°C at 0.1 GPa, ~490°C at 0.5 GPa and 710°C at 1.5 GPa.

Coherent nucleation followed by coarsening will have begun at Tat or a little below a coherent solvus curve (which is at T below the strain-free solvus) for feldspars with an ordered framework. Yund (1974) provided such a solvus curve for T >450°C, which Parsons et al. (2010, fig. 1) extrapolated to 300°C using a polynomial. The solvus is extremely steep at low T but Or93 lies on a further extrapolation of this curve to ~90°C at 0.1 GPa, ~180°C at 0.5 GPa and ~400°C at 1.5 GPa, assuming that the P-dependence recommended by Hovis et al. (1991) can be applied. We do not know the P at which the Perth pegmatite crystallized and in a protracted geological history it is possible that the pegmatite was subsequently buried more deeply. Whatever the P, coarsening kinetics below 200°C are too slow to have produced the observed lamellar periodicities (see Fig. 18 and next paragraph). We can be confident that exsolution and coarsening began at ≤400°C, with misfit dislocation formation at some lower T.

We can consider the kinetics of lamellar exsolution at low T in the light of experimental work. The most complete experimental data describing coherent coarsening in cryptoperthites are those of Yund and Davidson (1978). They annealed a disordered homogeneous alkali feldspar starting material, Ab65Or35, at 560–470°C, without water for time (t) up to 1.5 y and measured the periodicity (λ) of the film cryptoperthite that developed, using TEM. This annealing method provides the most realistic way to approach natural exsolution by diffusion because it includes the effect of coherency strain. However, the largest value of λ produced experimentally was 46 nm so that extrapolation to the μm scale of our samples (Figs 3a, 15a) is extremely large, and coherent exsolution began in our present samples at much lower T. Yund and Davidson also maintained an initially homogeneous sample at 530°C for 27 days at PH2O 200 MPa obtaining a similar periodicity to the ‘dry’ experiments, suggesting that the presence of water has no significant effect on coarsening rates. Hokanson and Yund (1986) compared Na–K interdiffusion coefficients from various studies and concluded that there was reasonable agreement, the main variable being crystal composition as the alkali feldspar solvus was approached and the solid solutions became more non-ideal. The effect of P on diffusion rates is unknown but likely to be small. Parsons and Fitz Gerald (2011) found good, order-of-magnitude agreement between observed lamellar periodicities of ordered film microperthites in the Klokken pluton and those extrapolated from Yund and Davidson's experiments to 104–105 y, corresponding with annealing times appropriate for a cooling history for the intrusion calculated by Brown and Parsons (1984a).

Brady (1987) carried out a least-squares analysis of Yund and Davidson's data and obtained an Arrhenius for coarsening corresponding with:
k=(2.076×1014)exp(139825RT)[k(m2s1),activation energyEa(Jmol1),T(K)]
Coarsening data are applied most readily to regular periodic intergrowths formed by spinodal decomposition, whereas the present intergrowths are irregular in distribution and formed by nucleation. However, provided we can be sure that there are no small lamellae intervening between large lamellae it is possible to estimate a maximum diffusion distance, λ/2. The rate constant k in (1) is equivalent to the diffusion coefficient D in the approximation x2 = Dt where x is the diffusion distance (m). A round-number estimate of the largest λ/2 in Fig. 16a is ~1 μm. The t calculated from (equation 1) to obtain an intergrowth with this diffusion dimension by isothermal annealing is shown as the lower curve on Fig. 18. It would require 0.11 My at 400°C, which would require P of ~1.5 GPa, 8.4 My at 300°C, ~1.0 GPa and 4.2 Gy at 200°C and ~0.5 GPa. While the first two values are feasible in crust undergoing regional metamorphism, coarsening by sustained annealing much below 300°C is clearly impossible. It may be that the extrapolation of the coherent solvus to the low T implied by the bulk composition of Or93Ab7 is in error, or that the coarsening rates determined experimentally do not apply at lower T. However, sustained heating in the range 400–300°C at moderately high P appears to be required to explain the strain-controlled film perthites in both pegmatites.

Perth vein macroperthite

The coarse perthite in Perth is a sub-periodic intergrowth of microcline and albite veins (Figs 2, 3) ~0.6 mm wide and spaced ~1 mm apart in the cryptoperthitic microcline matrix. The cryptoperthite formed after the development of tartan twinning in the microcline below 500–450°C (Figs 5, 6) and the veins formed after the cryptoperthite (Figs 3, 10), had coarsened in the range 400–300°C (Fig. 18), over a considerable time interval. The albite is of near end-member composition (~Ab99.2, Table 1), pointing to growth at very low T. The extreme irregularity of interfaces (Figs 3, 10), the development of subgrains and the accompanying turbidity, all point to formation by a replacement process involving interface-coupled dissolution and reprecipitation (Worden et al., 1990; Walker et al., 1995; Putnis, 2002; Parsons and Lee, 2009). Very coarse, sub-periodic vein intergrowths are frequently reported from pegmatites. Smith (1974, pp. 407–421) and Smith and Brown (1988, pp. 595–604) provide numerous illustrations. As we discuss below it is geologically implausible that such coarse intergrowths could form by diffusion.

Replacement in Perth is clearly non-isochemical because the bulk composition of the cryptoperthitic microcline (Or93Ab7, Table 1) is much less albitic than the bulk crystal (Or57Ab42An1). Chemically, only Na↔K exchange is involved in the replacement. An was below detection in the cryptoperthitic microcline and the replacive albite is An0.2 (Table 1). Long-range transport of Si and Al is not required. Dissolution of twinned microcline and replacement by albite subgrains presumably took place in advancing fluid films, as envisaged by Parsons and Lee (2009). Orville (1963) explained how alkalis are partitioned between an assemblage of two feldspars and an aqueous fluid, and how this could lead to alkali metasomatism (Orville, 1962). The importance of his work in feldspar microtextural evolution was reviewed by Parsons and Lee (2000). Provided the feldspars lie on the solvus, Na:K in the fluid is a function only of T. Fluids in equilibrium with two feldspars at low T have high Na:K, independently of the proportions of Ab- and Or-rich feldspar, and in a hydrothermal system with a T gradient will reach equilibrium by precipitating K-feldspar at low T and albite at higher T. The irregular microcline replacing albite in Fig. 8 would have been precipitated from a relatively cool fluid. Lee and Parsons (1998) found extensive replacement by microcline in feldspars from the Shap granite undergoing diagenesis. The dissolution of film albite lamellae leaving empty lenticular pores (Figs 7, 9) could also be a response to cooling. Elastic strain in coherent lamellae would mean that their albite would be more soluble than the unstrained albite mosaics forming the macroperthite.

Granitic pegmatites (like granites with low normative An) usually have bulk compositions corresponding with minimum melting compositions in Ab–Or–Q–H2O (e.g. London and Kontak, 2012). Orville (1960) showed that the compositions of the Keystone pegmatites correspond with liquidus minima in Ab–Or–Q at ~200 MPa (Tuttle and Bowen, 1958). The long established agreement (Tuttle and Bowen, 1958) between normative Ab, Or and Q calculated from analyses of granitoids and liquidus minima in the granite system precludes large-scale, subsolidus non-isochemical replacement at the scale of a rock sample, even when there is clear textural evidence for some non-isochemical replacement at the scale of a single alkali feldspar crystal. In the absence of data on the mineralogy of the pegmatite as a whole it is not possible to speculate on the source of the Na+, or the fate of the K+ that has been replaced.

Keystone vein perthite

The coarsest vein perthite in Keystone (Fig. 15a) is on a similar scale to that in Perth, but it is more variable in scale, not obviously periodic and is overall orientated close to {110}. Andersen (1928) suggested that this type of vein perthite is replacive and that the ~{110} orientation is defined by contraction cracks. Alling (1938) recognized that non-isochemical replacement is likely to be localized near crystal edges, or follow fractures and cleavages, as in Keystone. A process of infiltration, on various scales, into crack networks governed by the {110} cleavage, which is often well developed in pegmatitic feldspars, seems to us to account well for the microtextures in Keystone. Planes in {110} frequently develop in replacement perthites because of the growth of subgrains with the adularia (and pericline) habits (Worden et al. 1990; Parsons and Lee 2009). Figure 16 shows relics of cryptoperthitic film lamellae in a zone of sericitization surrounding the vein albite. The coarse albite veins therefore developed after the formation of the cryptoperthite at <300°C. The zone of altered K-feldspar suggests that the fluid that was responsible for introducing the vein albite also led to local incomplete recrystallization of the microcline cryptoperthite. However, this recrystallized zone cannot have supplied all the albite in the veins, because the Ab-content of the matrix is only 6 mol.% (Table 1) and the recrystallization is incomplete. The Ab-component cannot have come from further afield in the microcline matrix while leaving the albite film lamellae unmodified. Like Perth, the Keystone vein perthite developed by replacement that was non-isochemical with respect to the bulk feldspar crystal, and perhaps involved plagioclase in the pegmatite.

It is not obvious to us how coarse periodic replacement perthites like those in both Perth samples form (Figs 1, 2 and 3). Coarse perthitic intergrowths in pegmatitic feldspars are often subperiodic, sometimes on mm scales. A striking example was used for the cover of a special issue of The Canadian Mineralogist (vol. 46, pt. 6, 2008) dedicated to the work of J.V. Smith. Other examples can be found in Smith (1974) and Smith and Brown (1988). In this section we discuss possible mechanisms for their development.

Coarsening and amalgamation of semi-coherent microperthitic film lamellae

Lee and Parsons (1997) showed that in the Shap granite there was a late phase of large-scale albitization of orthoclase phenocrysts that started with the replacement of strained albite and Or-rich feldspar surrounding dislocations. The replacive albite then advanced into the Or-rich feldspar leading to irregular broadening of the microperthitic albite films (e.g. Lee and Parsons, 1997, figs 2, 3). Ultimately, large volumes of orthoclase were replaced. These replacive intergrowths clearly developed on the fine film lamellae but are not periodic over a large volume. Semi-coherent albite films are especially susceptible to interaction with fluids because of the misfit dislocations which are arranged in an orthogonal network over their surfaces (Aberdam, 1965; Waldron et al., 1994; Lee et al., 1995; Fitz Gerald et al., 2006). Once a fluid has gained access to one part of the dislocation network, dissolution or replacement can take place rapidly owing to the energetic advantage of destruction of strained crystal structure surrounding the dislocations.

In Perth and Keystone the strain-controlled microtextures show good evidence for localized reactions with fluids subsequent to coarsening, i.e. below ~300°C. In thin section the films are partly turbid. EM work shows that albite films have in places been dissolved (Figs 7, 9), or replaced by irregular microcline (Fig. 8). Albite outgrowths have replaced microcline adjacent to films (Figs 17b, c). It is difficult to see how a progression of this process could lead to the coarse albite veins in Perth. Figures 3b and 10 show that protrusions in the complex surface of the macroperthitic albite veins cut across matrix film lamellae, as they do in Keystone. The Ab-component could not have been extracted from the film microperthite. We conclude that local replacement of film lamellae (Figs 17b, c) is a minor, late process, perhaps related to formation of the coarse vein perthite, but not a step leading to its formation.

Modification of precursor coarse coherent intergrowths

The axes of the lenticular macroperthitic veins in Perth are slightly sinuous but overall roughly parallel to b (Fig. 2a) and will lie in or close to (100), not far from (6İ01), the plane of coherent film perthites. Lenticular lamellae in non-turbid meso-perthites in granulite facies rocks (see Rollinson, 1982, fig. 1; Evangelekakis et al. 1993, figs 2, 3; Cayzer, 2002; and Parsons and Lee, 2005, figs 16–18, for examples), which have periodicities up to ~20 μm, are in (6İ01). A possibility, therefore, is that the periodicity of the vein perthites in the pegmatites was derived from an initial phase of coherent exsolution at relatively high T modified by dissolution–reprecipitation reactions at <300°C. In this model the microperthitic film lamellae in the matrix microcline (seen in both Perth and Keystone) would have formed at low T in the stranded diffusion profile between the coarsened, high-T lamellae. Similar ‘stranded’ lamellae, or ‘platelets’ are common in alkali feldspars from granitic rocks (e.g. Lee et al. 1995, fig. 15 and Parsons et al. 2010, fig. 7).

Estimates of minimum T for crystal growth (as homogeneous crystals), and of maximum T for the commencement of unmixing can be calculated for the bulk compositions of Perth and Keystone (Table 1) using the asumptions given in the section on development of strain-controlled microtextures above. The upper curves on Fig. 18 show that geologically unreasonable annealing times would be required to produce coherent intergrowths with the >200 μm diffusion lengths (λ/2) implied by Perth, even when exsolution occurred at high P and T. These times rule out the possibility of a diffusion-controlled precursor to the periodic vein perthites. Note that, in contrast, the ≤20 μm periodicities of coherent and semicoherent film intergrowths in granulite facies feldspars could be produced by diffusion in t <107 y, geologically reasonable during granulite-facies metamorphism. Ternary meso-perthites from granulites usually have significant An, in some cases >10 mol.%, which would increase the T of the beginning of exsolution, but possibly slow coarsening rates because of Ca–Al coupling.

Strain-controlled replacement

If a coherent precursor for periodic vein perthites is improbable, their mode of formation remains mysterious. The complex, fractal-like shapes of the surfaces of lamellae in Perth (Fig. 3b) hint of self-organization during an interface-coupled replacement process, but the origin of the periodic interleaving is not obvious.

Norberg et al. (2011) have recently published an interesting experimental study of albitization of a homogeneous sanidine (from Volkesfeld, Eifel) using concentrated NaCl solutions at 500°C and 200 MPa, in experiments lasting up to 16 days. The T and chloride concentrations are both considerably higher than is likely for replacement in the pegmatite feldspars but the experiments nevertheless provide a possible solution to our problem. Norberg et al. found that angular albite blades with sharp, coherent or semicoherent interfaces penetrated the sanidine in a plane parallel to (100) or (h0l), where h is >>1 and therefore close to (6İ01). They suggest that interfaces favoured by replacement reactions are controlled by minimization of coherency strain, in the same way as coherent film exsolution lamellae, and they provide TEM images of both coherent and semicoherent interfaces between sanidine and replacive albite. The replacive albite is microporous, with a marked porosity fabric in (6İ01), and has a subgrain microtexture (their fig. 7) strongly reminiscent of the natural replacement microtextures imaged by Worden et al. (1990). Norberg et al.'s experiments are important because they show that replacement even of homogeneous sanidine may lead to intergrowths orientated by minimization of misfit between replaced and replacive phases, and might provide an explanation for the orientation of our coarse vein lamellae. In our samples development near the Murchison plane would be further enhanced by the presence of the semicoherent film lamellae, which predate the veins, and provide channels for replacement.

The albite–sanidine interface in the experiments of Norberg et al. (2011, fig. 2) was deeply serrated, with periodicities on the order of 50–200 μm. Their images are viewed from the b direction, and it would be interesting to know the appearance of the serrations from near c*, the viewing direction of the images in the present paper (Figs 3,10). In principle we might expect large serrations to grow at the expense of small ones, because total inter-phase surface energies and coherency strains would in that way be minimized. It is possible that a self-organized, periodic structure might arise similar to the coarse veins in Perth. During albitization there is a decrease in volume which might lead to cracking and favour the advance of larger albite films by providing space at the advancing film tip. The slight angular difference between film lamellae in (6İ01) and vein perthite in (100) (Smith, 1974, figs 19.4, 19.11) can be accounted for if the veins are composed of an assembly of replacive Albite-twinned {110} subgrains.

Pleated rims

Another way in which film lamellae might coarsen during fluid–feldspar reactions to a periodic structure is a process that leads to microtextures called ‘pleated rims’ along the margins of braid microperthite crystals. These crystals are meso-perthites (Ab60Or40) so this mechanism might apply to Perth (Ab42.0Or57.4An0.6) but will not apply to Keystone, unless there was a precursor film microtexture that has been obliterated. Lee et al. (1997) described the complex coarsening process in feldspars from the Klokken intrusion. Coarsening of the braid texture starts by a process of ‘phase separation’ in which Ab- and Or-rich lamellae thicken near crystal margins into structures called ‘pleats’. They form initially by volume diffusion, when the constraint of coherency strain on the orientation and thickness of the braid lamellae is relieved by adjustment in the crystal boundary. In the advancing ‘head’ of the pleat, lamellae in the braid orientation {6İ 6İ 1} rotate into the (6İ 0 1) orientation of film lamellae which develop misfit dislocations which facilitate fluid access into the crystal. These develop into sub-periodic ‘vein perthites’ which in some cases (figs 7a,b in Lee et al., 1997) extend entirely across mm-scale crystals. Similar structures at interfaces between braid and patch perthite within crystals undergoing deuteric coarsening are illustrated by Parsons and Lee (2009, fig. 5, point C). The periodicities, ~20 μm, are much smaller than the coarse vein perthites in the present study, but Klokken cooled comparatively rapidly and has not been subject to long periods of annealing (see Parsons and Fitz Gerald, 2011). The Klokken patch perthites are strikingly similar to those produced experimentally by Norberg et al. (2013).

An interesting feature of the coarse macroperthitic albite lamellae in Perth is the occurrence of dislocations on Albite twin composition planes (Figs 11, 12, 13 and 14). Similar dislocations occur in Keystone. Dislocations on the composition plane of Albite twins are anomalous because there is normally no lattice misfit and twins are fully coherent (Smith and Brown, 1988). Etch pits orientated in lines parallel to (010) were described on HF acid etched plagioclase by Lundström (1970). These pits, in an andesine (An45) and a pegmatitic oligoclase (An19), were interpreted like ours to have formed by the etching of dislocations on Albite twin composition planes. Textures of Albite twins in the andesine described by Lundström indicated a glide origin (i.e. the twins had formed in response to shear stress). The implication of Lundström's work is that the dislocations are genetically related to the formation of glide twins.

Smith and Brown (1988) summarize the criteria for differentiating growth and glide twins. Growth twins are usually of low to moderate frequency, often have stepped composition surfaces and may stop abruptly, and may thicken and thin independently of each other. Glide twins typically occur in clusters which change in thickness sympathetically, often taper to a point and are often related to internal deformational features. Albite twins in Figs 11, 12, 13 and 14 show considerable variation in thickness, often have steps in composition planes and on these criteria conform with growth twins, as would be expected from their occurrence in replacive subgrains. Small steps in composition planes are clearly associated with dislocations. The structural misfit at the curved end of an albite twin in Fig. 14 has been accommodated by an intense row of closely-spaced dislocations.

On the other hand, there are observations that support a shear-related origin for the dislocations. The grooves on the etched (001) surfaces of Albite twins (Fig. 12) are caused by differential etching reflecting an inhomogeneous distribution of elastic strain energy. The stress has been accommodated by compression of {110} planes. Dislocations are observed where regions of elastically strained crystal structure orientated parallel to (110) and (11İ0)albite intersect at the twin composition plane. This model is further supported by the fact that the strain fields surrounding the dislocations, which have been etched to form the pits, extend into the body of the Albite twin parallel to {110}.

Some observations suggest that formation of at least some of the dislocations post-dates Albite twinning. Some twins have no dislocations on either side, and lines of dislocations can branch off from the twin composition plane into the interior of the twin (Fig. 12). In addition, the irregularity in distribution of dislocations is curious; on one side of a twin individual many dislocations may be present, whereas on the other side they may be completely absent.

We suggest that most Albite twins formed during replacive growth, and that some dislocations formed to minimize misfit where the advance of a twin was terminated (Figs 11, 14). The periodic dislocation arrays at contacts between albite subgrains, and between albite and K-feldspar subgrains, produced experimentally by Norberg et al. (2011) and those imaged by Lee and Parsons (1997), between orthoclase and natural replacive albite, are of a similar type. Other dislocations, on straight Albite twin composition planes (Figs 12, 13), and the long-range strain (Fig. 12), developed subsequently during minor deformation.

The pegmatitic alkali feldspar from Perth, Ontario, supplied by Wards (46 E 0510) is a microcline macromesoperthite (bulk Ab42Or57An1). It differs both in microtextures and bulk composition from a sample of the type perthite (Hunterian M2631) (Ab56Or41An3) from the same general location. The sample from Keystone, South Dakota, (Wards 46 E 5125), is a microcline microperthite (Ab21Or78An1).

Perth microcline has a regular ‘tartan’ twin microtexture of sub-μm periodicity and does not have a sub-grain microtexture. The microcline formed by a continuous diffusional process. Keystone microcline has thicker, more variable, spindle-section twins. Subgrains occur, with associated micropores and volumes of irregular microcline. They formed by pervasive dissolution–reprecipitation. The microcline of both samples contains sub-μm coherent and semicoherent albite films close to (6İ 0 1). In Perth the Albite twins in the albite films have widths defined by twins in the microcline. Coherent exsolution occurred after the development of ‘tartan’ twinning, in the microcline field. The bulk composition of the microcline plus included albite films (Or93) implies that coherent exsolution would have begun at ~90°C at 0.1 GPa, ~180°C at 0.5 GPa and ~400°C at 1.5 GPa. Diffusion parameters imply sustained heating for between 0.11 My at ~400°C and 8.4 My at ~300°C to develop these microtextures. Implausibly long annealing would be required at 200°C. Some semicoherent lamellae were later affected by dissolution leaving lenticular pores, and some were replaced by irregular microcline. In Keystone, replacive incoherent albite outgrowths have developed on the lamellae.

Perth contains sub-periodic veins of very pure albite (Ab>99), close to (100), with extremely complex surfaces. They are up to 1 mm in thickness and separation, cross-cut the coherent micro-perthites, are constructed of incoherent and semi-coherent subgrains, and formed by interface-coupled replacement of the cryptoperthitic microcline. It is not obvious how the periodicity of coarse replacive perthitic intergrowths develops. Implausibly long times are required to produce mm-scale lamellae by diffusion, ruling out the possibility that they represent deuteric recrystallization of coarse coherent precursors. Experimental work by Norberg et al. (2011) shows that replacive lamellae can be orientated in (6İ01) [i.e. close to (100)] because they are initially coherent, and that advancing interfaces have a saw-tooth shape on scales of tens of μm. The periodic macroperthites might have formed in a similar way. In Keystone, coarse albite veins are not periodic and probably follow contraction cracks on the {110} cleavage. Replacement was non-isochemical on the scale of a single crystal but liquid–crystal relationships in the ‘granite’ system Ab–Or–Q require that the albite was locally derived.

Unusually, dislocations occur on Albite twin composition planes in the Perth vein albite. Some formed in response to coalescence of precursor albite films during fluid-induced coarsening. Curving arrays away from composition planes resulted from tectonic deformation. The microtextures in the Wards samples differ considerably from those encountered in alkali feldspars from granitic and syenitic rocks of normal grain-size. They are not suitable samples for obtaining generically applicable data on dissolution rates and thermoluminescence fading, for which they have been used in the past.

The authors thank the Natural Environment Research Council for funding this research through grant NER/A/S/2003/00346 and John Faithful, of the Hunterian Museum in Glasgow, for supplying material from the type perthite.

P1Freely available online through the publisher-supported open access option.